Apparently there are lot’s of differing opinions on antennas – now there’s a shocker 
Hopefully, we can put some rough numbers on things to help folks to figure out where opinion ends and basic principle begins.
Continue reading Low Gain Ground Mounted Antennas for LEO Satellites
6,399 total views, no views today
The 40 Meter Pixie (available at the time of writing for about $7 assembled on eBay) is an interesting minimalist transceiver design – crystal controlled, 2 transistors and an audio amplifier chip. And you are on the air with a unit that you can make QSO’s with! Naturally, there is much room for improvement, and it can in fact be done for only a few dollars more. Below I describe a set of additions that I think really enhances the Pixie’s usefulness.
9,188 total views, no views today
The unit on the left below is the medium power BMU (Base Matching Unit) intended for 42 foot to 48 foot vertical, sloper, or Inverted-L antennas. Naturally, these antennas (like all end-fed antennas) require a decent radial system for efficient operation on the lower bands.
6,621 total views, no views today
The unit on the right below is the QRP BMU (Base Matching Unit) intended for 42 foot to 48 foot vertical, sloper, or Inverted-L antennas. Naturally, these antennas (like all end-fed antennas) require a decent radial system for efficient operation on the lower bands.
4,569 total views, no views today
As part of renewed interest in portable medium power operations, I wanted a small cheap matcher. The units below are simply standard T-Tuners. Using dirt-cheap construction technique and commonly available parts, these units perform well at a very low cost.
Continue reading Still More Medium Power T-Tuners for Cheap
3,741 total views, no views today
As part of project LOAP (Lipstick On A Pig ===> http://vtenn.com/Blog/?p=1348), I wanted a small cheap matching and SWR indication unit for the Pixie-based transceiver system. The T-Tuner and SWR bridge unit on the right, in the picture below, is not vastly different from others, but here it is for your consideration as a good performer at a low cost. Note however, that it has been characterized into real-world impedances with a worst-case loss of less than 0.9 dB.
Continue reading Yet Another QRP Portable T-Tuner and SWR Bridge for Cheap
6,292 total views, no views today
Often one sees characterization and loss measurement of UNUNs using an SWR measurement of the UNUN when terminated in it’s transformation resistance, or with the “back-to-back” 2-x-Loss method. Each method reveals something about some quality of the UNUN, but neither method tell us much about how much power the UNUN will deliver to the actual antenna.
In this article I will show a simple method of measuring actual UNUN losses into the actual load impedances that the UNUN will see in service.
Continue reading “Z-Substitution” Method for Measuring UNUN Loss Into Real-World Load Impedances
4,715 total views, no views today
Excellent technical article regarding limited space antennas:
Continue reading Classic W8JI Limited Space Antennas Article
3,172 total views, no views today
I modeled a number of shortened dipoles with various capacitive hats at their ends. I think the results may interest you.
Continue reading Article by SP3L Modeling Various Configurations of Capacitance-Hat Dipoles
2,361 total views, no views today
The Pixie is a fun and popular QRP transceiver kit. However, typical output power on 40 M is only about 300 to 500 milli-Watts – a bit too QRPp at times…
In this article I’ll show cheap and easy ways to pump up the output power to around 1.2 or over 2 Watts, depending upon the power supply type and crystal activity.
Continue reading $3 to Quintuple the Output Power of a 40 M Pixie Transceiver
21,723 total views, 1 views today
